Floor Coatings

Specialty Coatings Inc. has partnered with Excelsior Coatings to offer a wide range of choices in floor coating systems. Excelsior has manufactured coatings since 1890 and is considered one of the industry leaders in floor coating technology. You're sure to find the ideal coating, seal, or finish for your particular floor. Whether your job requires waterbornes, urethanes, epoxies, rubber base sealers, or slip-resistant finishes, in clears or colors, from light-duty to the most severe industrial environments, we have a system that will meet your needs. Custom colors are available on orders of 50 gallons or more. For your convenience, please click here for an application chart.

WATERBORNE

These two-component, waterborne finishes are easy to apply
and provide an exceptional high gloss and durable finish. They
are also low in VOCs and have little odor. An excellent choice
when you need a low odor, non-flammable, tough coating.

8000 SERIES WATER BASED EPOXY

• Two-component, outstanding resistance to brake fluid,
  skydrol, etc.
• May be used on cured or uncured concrete.
• Unsurpassed for hardness, gloss and durability.
• Available in ten standard colors and a non-skid kit.
• Approved for use in USDA plants.

8001 SERIES CLEAR EPOXY SEALER

• Same durable two-component epoxy coating, but in a
  clear formula.
• May be used as a single coat clear sealer or as a primer
  before applying pigmented epoxy finish coat (8000
  series), 100% solid epoxy (8005), or moisture cure
  urethane (9640).

SOLVENT BORNE

6000 SERIES EPOXY ESTER

• Economical single-component solvent based, gloss coating formulated to
  provide additional chemical resistance beyond typical alkyd and OMU
  finishes.
• Abrasion and mild chemical resistant, this coating is suitable for interior use
  on wood, concrete and metal where a general duty floor finish is desired.

8005 TWO-PART EPOXY RESURFACER

• 100% solids epoxy coating designed to fill and smooth interior concrete that
  is pitted, worn, or spalled.
• Forms a clear, high-gloss finish with outstanding abrasion and chemical
  resistance.
• May also be used as a heavy duty, chemical-resistant coating.
• Standard color is clear, but custom colors are available with orders of 50 gallons
  or more.

8006 EPOXY CONCRETE PATCH

• Three-component light gray epoxy patch to fill eroded, cracked, or damaged
  concrete.
• 100% solids formulation exhibits minimal shrinkage upon curing.
• Outstanding abrasion and chemical resistance.
• Cured patch is stronger than concrete, but not intended for repair of structural
  defects.

9640 MOISTURE CURE URETHANE

• Single-component, high gloss coating offering ultimate hardness and
  chemical resistance.
• Outstanding resistance to abrasion, marring, and scuffing as well as foot,
  forklift and other vehicular traffic.

1240 URETHANE CONCRETE SEAL

• Oil-modified polyurethane floor coating designed to seal interior or exterior
  concrete.
• Resists abrasion, marring, repeated washing, rubber burns, imprinting,
  mild chemicals, and wear from pedestrian or forklift traffic.

4010 INTERIOR & EXTERIOR SEAL

• Penetrating, non-yellowing, rubber base waterproofing sealer used on
  interior or exterior concrete, masonry, brick, stone, wood and other porous
  substrates.
• Resists degradation from sunlight and mild chemicals.
• Dries to clear film that resists water penetration as well as dirt, salt, oil,
  grease, and other contaminants.
• Ideal for parking decks, ramps, sidewalks, garage floors, and pavers.

4130 STONE/MASONRY/TERRAZZO SEAL

• Lower solids rubber base sealer.
• Allows deeper penetration of the binder while imparting less surface film.
• Designed specifically as a waterproofing sealer to ornate substrates.
• Fills pores to inhibit water, dirt, salt and other contaminants from penetrating
  without altering the color and texture of the substrate.